To open the Control-M JCL Verify Defaults panel (see the following figure), enter JD in the option line in the IOA Primary Option Menu. Adjust the verification criteria settings or accept the current ones. The default settings are specified in the CTJPARM member.
Fig.JV.6.3 Control-M JCL Verify Defaults panel
-------------- CONTROL-M/JCL VERIFY DEFINITION FACILITY - ENTRY PANEL ------------
COMMAND ===>
ENTER THE PARAMETERS BELOW:
PROCDD=> LINKDD=>
NODE=> LOCAL SYSTEM=> IOA ENV=> LOCAL AUTO ROUTE=> D (Y/N/D)
SUMMARY FORMAT ===> D (T/M/N/D) T - TABLE M - MESSAGES N - NO SUMMARY D- DEFAULT
MESSAGE ID ===> D (Y/N/D) Y - SHOW MSGID N - HIDE MSGID
RULE TRACE ===> D (Y/N/D) SHOW RULE INFORMATION
SPECIFY VERIFICATION CRITERIA
JES SYNTAX ==> D (Y/N/D)
DATASET VERIFICATION ==> D (Y/N/S/U/D) CNDALC=> D (Y/N/D)
DATASET AUTHORIZATION ==> D (Y/N/D)
PROGRAM EXISTENCE ==> D (Y/N/D)
RESOLVE CONTROL-M AUTO-EDIT VARIABLE ==> D (Y/N/D)
SITE STANDARDS RULES ==> D (Y/N/D) ENV => GENERAL
UTILITIES VALIDATION ==> Y (Y/N/D)
MESSAGE LEVEL ==> D (I/W/E/D)
USE Y - ALWAYS CHECK N - NEVER CHECK S - NO SPACE CHECK U - UTITIES CHECK
E - ERRORS W - WARNING I - INFORMATION D - DEFAULT
The following table describes the configuration parameters of the Control-M JCL Verify Defaults panel. These parameters are only available under the ISPF editor.
Tab.JV.6.1 Control-M JCL Verify Defaults panel parameters
Criteria |
Description |
---|---|
PROCDD |
Name of a predefined DD card from which the procedures are resolved when the JCLs are verified. For example, PROC01. The DD card must be predefined in JES PROCLIB or in the CTJPRC member and will be the only procedure library searched. For more information, see JES2/3 Predefined PROCLIBs. |
LINKDD |
Name of a predefined DD card in which the load modules are searched when the JCLs are verified. For more information, see CTJLINK – User link libraries for program existence check. |
NODE |
Indicates the computer where the verification is being performed. |
SYSTEM |
Identifies the target SYSTEM in the target SYSPLEX. Default: A blank specifies any SYSTEM in the target SYSPLEX. Preference is given to SYSTEM with the same name as the originating SYSTEM, when IOA ENV is not blank or *. |
IOA ENV |
Identifies the target CTJMON by the QNAME of the IOA environment in the target SYSPLEX/SYSTEM. Default: A blank specifies any IOA environment in the target SYSPLEX. Preference is given to the same IOA environment as that of the originating CTJMON when SYSTEM is not blank or *. Masking: * has the same meaning as blank |
AUTO ROUTE |
Enables automatic routing so the JCL can be verified on different Control-M JCL Verify monitors located in different systems, depending on JES routing commands and JOB card routing keywords. Valid values are:
|
SUMMARY FORMAT/ SUMMFRMT |
Display format for the message summary section. Valid values are:
|
MESSAGE ID/ MSGID |
Display message ID. Valid values are:
|
RULE TRACE |
Display triggered rule information ID. Valid values are:
|
The following table describes the criteria for verifying the JCL members.
Tab.JV.6.2 Control-M JCL Verify verification criteria
Criteria |
Description |
---|---|
JES SYNTAX |
Whether to verify that the JES2 or JES3 statements are correct. Valid values are:
|
DATASET VERIFICATION |
Whether to verify dataset. Valid values are:
|
CNDALC |
Whether to consider datasets that are created or deleted by conditional steps as conditional references, and issue warnings when the dataset is referenced by a step later in the job if this reference may not be valid.
For more information and examples, see Conditional dataset references. |
DATASET AUTHORIZATION |
Whether to verify file access privileges. Valid values are:
|
PROGRAM EXISTENCE |
Whether to verify that the load modules exist. Valid values are:
|
RESOLVE CONTROL-M AUTO-EDIT VARIABLE |
Whether to resolve Control-M AutoEdit variables in the job. Valid values are:
|
SITE STANDARDS RULES |
Whether to verify site standards. Valid values are:
In the ENV field, specify which rules, in addition to the GENERAL rules, are to be used in the site standard verifications. The default value is GENERAL, indicating that only the GENERAL rules are to be used in the verifications. |
UTILITY VALIDATION |
Whether to verify the syntax of the IBM utilities (for details, see JCL and syntax verification) and the DB2 related validation. Valid values are:
Note:
|
MESSAGES LEVEL |
The minimum level of message severity to be issued. Valid values are:
|
The criteria are associated with each user and are saved in the following profile variables:
Parent Topic |