|
|
|
|
|
This group includes messages for the Control-M for z/OS, Control-M/Assist, Control-M/Links for z/OS, and Control-M/Restart products.
Explanation: This information message indicates that the Control-M monitor has stopped processing jobs temporarily to allow the New Day procedure to begin execution.
Control-M suspends processing at the time specified in CTMPARM to allow the New Day procedure to run.
The Control-M monitor remains suspended until the New Day procedure ends. At the successful completion of the New Day procedure, the monitor resumes normal execution.
Corrective Action: No action is required.
Explanation: In general, this message indicates that the Control-M monitor resumed processing jobs after the New Day procedure completed successfully. However, under the Control-M monitor operator command /F CTMTROLM,NEWDAY=NOW,ORDERONLY, this message can appear before the Newday procedure ends.
Corrective Action: No action is required.
Explanation: This message indicates that all phases of New Day Processing for the specified monitor ended successfully. However, under the Control-M monitor operator command /F CTMTROLM,NEWDAY=NOW,ORDERONLY, this message can appear before the Newday procedure ends.
The Control-M monitor resumes execution.
Corrective Action: No action is required.
Explanation: Highlighted, unrollable message.
The Control-M monitor received no indication that the New Day procedure began processing.
The Control-M monitor requests the start of the New Day procedure, and periodically checks the progress of the procedure. This message is issued when the monitor does not receive any indication that the New Day procedure started executing.
The Control-M monitor issues message CTML06W or RUNL06W to ask the operator how to proceed.
Corrective Action: No action is required.
Explanation: Highlighted, unrollable message.
The Control-M monitor detected that the formatting of the Active Jobs file (AJF) did not complete successfully within a specified time interval.
The Control-M monitor issues message CTML06W or RUNL06W to ask the operator how to proceed.
Corrective Action: No action is required.
Explanation: Highlighted, unrollable message.
During follow-up of the New Day procedure, the Control-M monitor detected an abnormal condition.
The Control-M monitor issues message CTML06W or RUNL06W to ask the operator how to proceed.
Corrective Action: Reply R for retry. If the message is reissued, note the phase number and reply E to terminate the monitor. To reactivate the monitor, run the Control-M New Day procedure, and when it completes successfully, restart the monitor. Give BMC Customer Support the phase number specified in this message and the Control-M monitor full output.
Explanation: Highlighted, unrollable message.
While checking the progress of the New Day procedure execution, the Control-M monitor detected an error.
This message is accompanied by a message explaining the cause of the problem.
The Control-M monitor waits for a reply to this message.
Corrective Action: Type R or E and press Enter, with the following results:
Explanation: Normal message of Control-M monitor when it stops processing jobs temporarily to allow the New Day procedure to begin execution.
Control-M suspends processing at the time specified in CTMPARM to allow the New Day procedure to run.
The Control-M monitor remains suspended until the New Day procedure is successfully completed. Upon successful completion of the New Day procedure, the monitor resumes normal execution.
Corrective Action: No action is required.
Explanation: Highlighted, unrollable message.
Control-M monitor found no indication that New Day procedure completed execution.
The Control-M monitor issues message CTML06W or RUNL06W to ask the operator how to proceed.
Corrective Action: No action is required.
Explanation: Highlighted, unrollable message.
Allocation of the dual IOA Conditions file or the dual Active Jobs file (AJF) failed, but processing continues because system parameters have indicated that this condition should be ignored.
Wish WM1944 in the IOADFLTS member of the DOC library was activated to allow an allocation error for dual files to be ignored. (If the wish has not been applied when an allocation error occurs, Control-M terminates execution.)
The Control-M monitor continues normal execution.
Corrective Action: If you require dual file processing, do the following:
Explanation: This message is issued in response to the following operator command:
F CONTROLM,NEWDAY= expression
Special NEWDAY processing is performed as specified in expression. For more information, see the INCONTROL for z/OS Administrator Guide, “CTM,” “Special Newday Parameters.”
Corrective Action: No response required.
Explanation: In response to the F CONTROLM,NEWDAY=SKIP operator command, Newday processing is skipped.
NEWDAY processing normally scheduled to begin at hh:mm is bypassed due to the special NEWDAY command. For more information regarding the special NEWDAY commands, see the INCONTROL for z/OS Administrator Guide, “CTM,” “Special Newday Parameters.”
Corrective Action: No response required.
Explanation: This informational message is issued at the time scheduled for Newday processing (according to the DAYTIME parameter in CTMPARM). Newday processing is skipped as a result of one of the following commands:
Newday processing is skipped. For more information regarding the special NEWDAY commands, see the INCONTROL for z/OS Administrator Guide, “CTM,” “Special Newday Parameters.”
Corrective Action: No response required.
Explanation: The S CONTROLM,NEWDAY= expression command was entered with an invalid value of expression. In this command, the only valid value for expression is SKIP. For more information, see the INCONTROL for z/OS Administrator Guide, “CTM,” “Special Newday Parameters.”
The command is ignored
Corrective Action: Correct and re-enter the NEWDAY command.
Explanation: This information message indicates that the RESUME request submitted by the user has been accepted.
Corrective Action: No action is required.
Explanation: The Control-M monitor stopped journaling updates to the Active Jobs file due to a detected error.
The error which caused journaling to be terminated is described in earlier messages.
WTOR message RUNL12W is displayed, enabling the user to continue without the Journal facility or to shut down the Control-M monitor.
Corrective Action: Respond to message CTML12W.
Explanation: This WTOR message is displayed when the Control-M Journaling facility is shut down.
This message may be preceded by messages explaining the reason for Journaling facility shutdown. This message also appears after running the restoration utility successfully to provide an opportunity to reset the journal file. The user can run the restoration utility repeatedly (perhaps to different end times) before initializing the journal file.
Responses to this WTOR message allow the user to continue Control-M without journaling, or to shut down Control-M so that a problem can be fixed.
The Control-M monitor waits for a reply to this message.
Corrective Action: See preceding messages for information describing why journaling was stopped.
Specify one of the following values as a response to this message:
Explanation: This information message is issued when the user specified C in response to WTOR message CTML12W.
The Control-M monitor continues normal execution. The Journal file is no longer updated.
Corrective Action: No action is required.
Explanation: The user attempted to enable/disable the Control-M Journal or History allocation for space reuse functions. However, the current fileStatus status of this facility already complies with the user request.
The command is ignored.
Corrective Action: No action is required.
Explanation: This information message is issued in conjunction with message CTM863W, which indicates that the Active Jobs file (AJF) is nearly full. Both messages are issued when the threshold value specified by the AJFTHRSH CTMPARM parameter is reached.
Corrective Action: Increase the size of the AJF using the CTMCAJF utility.
Explanation: This information message displays the MODIFY command (cmd) entered for the Control-M monitor.
Corrective Action: No action is required
Explanation: This information message displays the current value of QUIESTIME (the Control-M monitor planned shutdown time), where yyyy is one of the following values:
This message is added to the System Log.
Corrective Action: No action is required.
Parent Topic |