|
|
|
|
|
This group includes messages for the Control-D, Control-D/Image, and Control-D/Page on Demand products.
Explanation: This information message indicates that the CTMRSTR restoration utility has begun processing.
Corrective Action: No action is required.
Explanation: This information message indicates that the CTMRSTR restoration utility has completed processing.
Corrective Action: No action is required.
Explanation: Journaling was not activated because JRNL is set to N in the CTMPARM member in the IOA PARM library. In such a case, the Control-M monitor does not record events in the journal file. Consequently, restoration of the Active Jobs File from the journal file is not possible.
The restoration utility terminates processing.
Corrective Action: To use the restoration utility, the Control-M monitor must be run with the JRNL parameter set to Y in CTMPARM.
Explanation: An unrecognized parameter was specified for the CTMRSTR utility.
The CTMRSTR utility terminates.
Corrective Action: Correct the specified parameter and rerun the CTMRSTR utility.
Explanation: An invalid format was used for the value specified for the ENDTIME parameter in the CTMRSTR utility.
The ENDTIME parameter indicates when to restore the Control-M Active Jobs file and/or the IOA Conditions file.
The CTMRSTR utility terminates.
Corrective Action: Correct the value for the ENDTIME parameter and rerun the CTMRSTR utility.
Explanation: A parameter was specified more than once for a run of the CTMRSTR utility. Each parameter for this utility can be specified only once for each run of the utility.
The CTMRSTR utility terminates.
Corrective Action: Correct the parameters for the CTMRSTR utility and rerun the utility.
Explanation: No input parameters were specified for the CTMRSTR utility.
The CTMRSTR utility terminates.
Corrective Action: Specify the necessary parameters following the SYSIN DD statement and rerun the utility.
Explanation: Insufficient storage is available for the CTMRSTR utility.
The CTMRSTR utility terminates.
Corrective Action: Increase the region size and rerun the utility.
Explanation: The last record in the Journal file was not a syncpoint record.
Syncpoint records are used to verify all records added to the Journal file,. Only data records written to the Journal file prior to a syncpoint record are considered valid for restoration. The last syncpoint record is missing (due to an MVS system crash, cancellation of the Control-M monitor, or the like).
Records written after the last syncpoint record are not restored.
Corrective Action: No action is required.
Explanation: This information message indicates that the CTMRSTR utility ended due to an error. This message follows error messages that describe the error that caused the utility to terminate.
Corrective Action: Consult previous error messages, correct the error if possible, and rerun the restoration job. If CTMRSTR terminated due to a severe error (as indicated by message RSTU12E above), contact BMC Customer Support.
Explanation: The CTMRSTR utility terminated due to an internal error.
In this message, rsn is the code that indicates the reason for the error.
Corrective Action: Rerun the CTMRSTR utility with DEBUG set to (73:74) as specified in the restoration procedure. Contact BMC Customer Support. Provide the IOA representative with the message, the reason code, and any data produced by the rerun procedure.
Explanation: This information message indicates that the CTMRSTR utility completed the restoration successfully. Restoration of the Active Jobs file and/or the IOA Conditions file was successful.
Corrective Action: No action is required.
Explanation: The ENDTIME parameter for the CTMRSTR utility specified a time value that was older than the last time value found in the Journal file.
The CTMRSTR utility processes all records in the Journal file and execution proceeds normally.
Corrective Action: No action is required.
Explanation: The journal used by the CTMRSTR restoration procedure does not match the Active Jobs file used by the Control-M monitor to produce journal records.
In this message, fldname is the field name in the Active Jobs file that did not match the corresponding field in the Journal file.
The CTMRSTR utility terminates.
Corrective Action: Specify the correct Active Jobs file procedure for the CTMRSTR utility and rerun the utility.
Explanation: The journal file used by the CTMRSTR restoration utility is not compatible with one of the following parameters specified in the CTMPARM member in the IOA PARM library:
In this message, fldname identifies the problematic parameter.
The CTMRSTR utility terminates.
Corrective Action: Specify the correct CTMPARM parameters for the CTMRSTR utility and rerun the utility.
Explanation: The ENDTIME parameter specified a time earlier than the earliest timestamp in the Journal file.
The CTMRSTR utility terminates.
Corrective Action: Specify a value for the ENDTIME parameter which is consistent with the data in the journal file. This value must be later than the most recent New Day processing.
Explanation: This information message indicates that the specified Journal file corresponds to the Active Jobs file defined in the CTMRSTR restoration procedure.
The restoration process begins.
Corrective Action: No action is required.
Explanation: The CTMRSTR restoration utility encountered an error while attempting to restore a prerequisite condition.
The error is described in the sysout referenced by the DAPRINT DD statement.
The CTMRSTR utility terminates.
Corrective Action: The message in file DAPRINT describes the cause of the error. If the problem cannot be fixed, notify BMC Customer Support.
Explanation: The CTMRSTR utility could not run because the Control-M monitor was active.
The CTMRSTR restoration utility terminates.
Corrective Action: Shut down the Control-M monitor and rerun the restoration utility.
Explanation: The restore utility could not access the Active Jobs File because it was being used by another job.
The restoration utility waits until the file is accessible.
Corrective Action: No action is required.
Explanation: The restoration utility terminated processing because Control-M Application Server Gateway is active.
Corrective Action: Shut down the Control-M Application Server Gateway and rerun the restoration utility.
Parent Topic |