Messages CTW900 through CTW9xx

This group includes messages for the Control-M for z/OS, Control-M/Assist, Control-M/Links for z/OS, and Control-M/Restart products.

CTW912S ERROR IN CONTROL- x INSTALLATION PARAMETERS - INVALID DAYTIME

Explanation: Invalid format of Control- x Installation DAYTIME parameter. DAYTIME is the start time of the Control-M work day in your installation. Valid formats are +hhmm or -hhmm.

For more details see the section that describes installation parameters in the chapter for the appropriate products in the INCONTROL for z/OS Installation Guide.

The requested function terminates.

Corrective Action: Call your system programmer to correct the DAYTIME parameter in the CT xPARM member.

CTW913S OPEN OF DDNAME "SYSPRINT" FAILED

Explanation: The opening of a print file failed.

Possible causes are:

• The DD statement SYSPRINT is missing.
• The data set referenced by the DD statement SYSPRINT cannot be accessed for sequential write.

The program stops executing.

Corrective Action: Correct the JCL and submit again.

CTW914S ERROR IN IOA INSTALLATION PARAMETERS - INVALID DATETYP

Explanation: Highlighted, unrollable message.

The DATETYP IOA Installation Parameter is invalid. DATETYP is the type of date format used in the installation. Valid formats are:

• A - mmddyy
• W - ddmmyy
• J - yymmdd

For more details refer to the section that describes how to set IOA installation parameters in the IOA chapter of the INCONTROL for z/OS Installation Guide.

The requested function stops.

Corrective Action: Call your system programmer to correct the DATETYP parameter in the IOAPARM member.

CTW916W PROGRAM pgm WAITING FOR resourceName

Explanation: One of the IOA monitor internal programs detected an IOA resource in use by a TSO user or batch job. This message normally appears a few times a day.

The variables in this message are:

• pgm - the name of the internal program that is waiting for the resource that is in use
• resourceName - the name of the resource that is in use

Valid values are:

The message is displayed on the operator console.

Corrective Action: The user response depends on the circumstances, as follows:

• If the message appears many times every few seconds, the file may be hung. This situation must be resolved by determining which program is holding the specified resourceName. Look for the IOA QNAME that is specified in the IOA Installation Parameter and take appropriate corrective action.
• If pgm is CTMFRM and resourceName is CONTROLM, some possible reasons are:
• there are several Control-M monitors running with the same QNAME
• there is a user daily job running that has a date control record in which columns 60 through 65 are not blank, meaning that it is acting as the Control-M New Day procedure and therefore Control-M has been enqueued
• the Control-M New Day procedure was started externally (manually) rather than being started by the monitor, and as a result waits for the monitor to be suspended

Take appropriate corrective action.

• If the program name pgm is CTMJES and the resourceName is JES_SSRQ, then Control-M (in its postprocessing phase) has called the JES2 interface using IEFSSREQ (a JES2 subsystem request) and is waiting for some function to be executed by JES2, but the execution of that function is being delayed in JES2. If the message persists in this situation, prepare the Control-M monitor full output and contact BMC Customer Support.

CTW918S INSUFFICIENT MEMORY TO RUN CONTROL- x

Explanation: Highlighted, unrollable message.

More memory is required for the INCONTROL monitor.

The specified monitor will shut down.

Corrective Action: Increase the REGION size of the specified monitor.

CTW919S INTERNAL ERROR IN CONTROL-M MONITOR

Explanation: Highlighted, unrollable message.

An internal error occurred in the Control-M monitor.

The Control-M monitor abends with the user abend 0008.

Corrective Action: Try to start the Control-M monitor again. In any case, keep the dump and call BMC Customer Support for assistance.