Figure 9 CONTROLR step messages – Example 1
18.43.53 CTR001I CONTROL-M/RESTART REL 6.1.00-980B STARTED FOR JOB PRDJBGL5
18.43.53 CTR008I PROCESSING PARAMETERS: RR,PRDJBGL5,000BU,RL,.STEP005,,ACS
The first message above indicates that Control-M/Restart restarted the job. The second message displays the restart parameters that were passed to the CONTROLR step.
Figure 10 CONTROLR step messages – Example 2
EXCLUDE DSN SYS1*
EXCLUDE DSN IPO1*
The prefixes of data sets to be excluded from File Catalog and GDG Adjustment processing (as defined in the $DEFAULT or $EXCLUDE members) are listed (above).
Figure 11 CONTROLR step messages – Example 3
* THIS SUBSECTION CONTAINS DIRECT ACCESS DEVICE DEFINITIONS *
UNITNAME SYSDA DEVICE DASD
UNITNAME SYSALLDA DEVICE DASD
UNITNAME DISK DEVICE DASD
UNITNAME DIRECT DEVICE DASD
* THIS SUBSECTION CONTAINS UNIT RECORD DEVICE DEFINITIONS *
UNITNAME TAPE DEVICE TAPE
UNITNAME TAPEC DEVICE TAPE
UNITNAME CASSET DEVICE TAPE
UNITNAME TAPEHI DEVICE TAPE
UNITNAME TAPE* DEVICE TAPE
The correspondence between generic unit names and device types are listed from the user-defined $DEFAULT member.
Figure 12 CONTROLR step messages – Example 4
DEFAULT UNITNAME TAPE DEVICE TAPE
DEFAULT UNITNAME TAPEHI DEVICE TAPE
.
.
.
DEFAULT UNITNAME 3350 DEVICE DASD
DEFAULT UNITNAME 3380 DEVICE DASD
DEFAULT UNITNAME 3390 DEVICE DASD
*
*PARAMETERS SPECIFIED USING ONLINE:
*
RECAPTURE ABEND CODE=YES/NO
RECAPTURE COND CODE=YES/NO
STEP ADJUSTMENT=YES/NO
*
SUMMARY OF PARAMETERS IN EFFECT:
*
RECAPTURE ABEND CODE=YES/NO
RECAPTURE COND CODE=YES/NO
STEP ADJUSTMENT=YES/NO
*
14.37.58 CTR059I =========== ANALYZE PHASE STARTED ===========
14.37.58 CTR041I DATASET WILL BE SCRATCHED FROM VOLUME "WORK01"
14.37.58 CTR042I DATASET WILL BE UNCATALOGED
14.37.58 CTR038I DSN=CTR.GEN.SAS.G0042V00 DD=SYSUT2 STEP=COPY PROCSTEP=
14.38.03 CTR060I ========== EXECUTION PHASE STARTED ==========
14.38.03 CTR085I DATASET "CTR.GEN.SAS.G0042V00" SCRATCHED FROM VOL=WORK01
14.38.03 CTR090I CORRECTING REFERENCE OF GDG DATASET TO "CTR.GEN.SAS.G0041V00"
FROM:
14.38.03 CTR038I DSN=CTR.GEN.SAS.G0042V00 DD=SYSUT2 STEP=COPY PROCSTEP=
14.38.03 CTR082I RESTARTING FROM STEP COPY . TO STEP STEP09 .
14.38.03 CTR003I RESTART OF JOB M0500012 ENDED SUCCESSFULLY
Definitions of unit names are built into Control-M/Restart and need not be duplicated in either the $DEFAULT member or the member specifically named in the PARM field.
Some Control-M/Restart messages, including those listed above, are described in Table 35.
Table 35 Control-M/Restart Messages
Message |
Description |
---|---|
CTR059I |
Control-M/Restart works in two phases. The first phase analyzes what is done. |
CTR060I |
The second phase actually executes the necessary adjustments (delete data sets, adjust generation numbers, and so on). |
CTR147I/CTR038I |
Control-M/Restart adjusts the generation number. |
CTR041I/CTR042I |
As part of the File Catalog and GDG Adjustment facility, the data set must be scratched and uncataloged. |
CTR043E/CTR038I |
A data set needed for restart does not exist. In this case the missing data set is a temporary data set that MVS deleted at the end of the previous unsuccessful run. Control-M/Restart determines a step from which restart can be successfully performed. |
CTR039I |
Control-M/Restart has determined that the job can be restarted from STEP003. |
CTR081I |
Control-M/Restart recaptured condition codes from the previous run of the job. |
CTR090I/CTR038I |
Control-M/Restart has corrected the generation numbers for GDG data sets. |
CTR085I/CTR087I |
The data set has been successfully scratched and uncataloged. |
CTR082I |
This message indicates the step range that the restarted job executes. |
CTR003I |
Control-M/Restart has completed the re-start of the job successfully. Of course, at this point the result of the execution of the restarted job is not known. |
Parent Topic |