Messages REP300 through REP3xx

This group includes messages for the Control-D, Control-D/Image, and Control-D/Page on Demand products.

REP304E xxxxxxx NOT OK WITH cc Y REASON CODE zzzz MQ NAME uuuuuuu

Explanation: An error was detected during interface with IBM WebSphere MQ Series.

The variables in this message are:

• xxxxxxxx - which can be one of the following interface functions:
  • MQCONN
  • MQDISC
  • MQOPEN
  • MQGET
  • MQPUT
  • MQCLOS
  • MQCOMMT
• cc - the completion code, which can be
  • 0
  • 1,,,
  • 2
• zzzz - the reason code, which can have many different values. More detailed information about reason codes is included in the IBM WebSphere MQ Series documentation set.

System action is determined by the completion code and reason code combination. More detailed information about these codes is included in the IBM WebSphere MQ Series documentation set.

Corrective Action: User response to a particular completion and reason code combination is determined by that combination. More detailed information about these codes is included in the IBM WebSphere MQ Series documentation set.

REP305E INSUFFICIENT MEMORY TO DECOLLATE MESSAGE FROM MQ

Explanation: Insufficient memory to decollate the message from the IBM WebSphere MQ queue.

Corrective Action: Increase the Control-D monitor REGION size.

REP306E IOAUCODE INITIALIZATION FAILED RC rc REASON rsn

Explanation: An error was detected during initialization of the table used in the translation of an XML report or in the checking of Xpath values of the mission definition. The message can be issued from

• the R screen
• the A.Z screen
• the Control-D monitor

Possible causes of this error are:

• the ENCODTBL member was not found in the IOA IOAENV library
• the ENCODTBL member contains more than 100 entries
• some other internal error

The following system actions occur:

• Mission definition edition is terminated. Message IOAE2FS issues on the R.S and A.Z screens.
• The translation of the XML report does not proceed. Control-D continues processing.

Corrective Action: Perform the following actions:

1. Check the ENCODTBL member in the IOA IOAENV library, make any necessary corrections, reactivate the IOA Online facility, and continue the mission definition edition.
2. Check the ENCODTBL member in the IOA IOAENV library, make any necessary corrections, reactivate Control-D, and run this mission again.

If the problem persists contact BMC Customer Support.

REP307E UNICODE TRANSLATION FAILED RC rc REASON rsn

Explanation: An error was detected during translation of an XML report to EBCDIC or during the checking of Xpath-values of the mission definition for XML reports. The message can be issued from

• the R screen
• the A.Z screen
• the Control-D monitor

The variables in this message are:

• rc - the return codeValid values are:
  • 4 - incomplete translation, due to separator (FF)
  • 8 - the encoding pair that was specified in ENCODTBL is not supported
  • 12 - the input data in the XML report was incorrect
  • 16 - internal error: incorrect parameters
  • 20 - one of the members that was specified in ENCODTBL was not found in the IOA IOAENV library
• rsn - the code that disclosed the detailed reason for the internal error

The following system actions occur:

• Mission definition edition is terminated. Message IOAE2FS issues on the R.S and A.Z screens.
• The translation of the XML report does not proceed. Control-D continues processing.

Corrective Action: Perform the following actions:

1. Check the ENCODTBL member in the IOA IOAENV library, make any necessary corrections, reactivate the IOA Online facility, and continue the mission definition edition.
2. Check the ENCODTBL member in the IOA IOAENV library, make any necessary corrections, reactivate Control-D and run this mission again.

If the problem persists contact BMC Customer Support.

REP308I SYNCHRONIZATION WITH BACKUP/CTDDELRP ENDED

Explanation: This information message indicates that the synchronization process has finished.

Control-D received notification from the CTDDELRP utility or from the Backup Mission that the synchronization ended; therefore the decollating task on the monitor may resume. See message MONA59I for an explanation of the synchronization process.

Control-D continues the previously interrupted decollating tasks.

Corrective Action: No action is required.

REP309I SHUT DOWN UPON REQUEST OF MAIN TASK

Explanation: This information message indicates that Control-D monitor has been shut down.

Shut down of Control-D internal decollating task by request of the Control-D main task.

The Control-D monitor will shut down.

Corrective Action: No action is required.

REP30AI MQ DECOLLATION IS STOPPED

Explanation: The MQ interface process has stopped.

This message can appear for two reasons:

• The STOPMQ modify command was issued
• Errors occurred during MQ interface

Corrective Action: If errors occurred during MQ interface, review the LOG to determine the cause, make appropriate corrections, and issue the STARTMQ modify command.

REP30BE LOADING OF MODULE OF MQ STUB IS FAILED, THE NAME IS mmmmmmmm

Explanation: The prefix.prefixLOAD library is not installed or the IBM WebSphere MQ Series is not installed for the user, but an MQ decollation mission was defined.

The CTD30AI message will be issued and IBM WebSphere MQ decollation will be stopped.

Corrective Action: If the IBM WebSphere MQ Series is not installed, delete the MQ mission. Otherwise correct your installation configuration and then issue the STARTMQ modify command.

REP30CE ANY OF MQ QUEUES CAN NOT BE OPENED

Explanation: Control-D tried to retrieve a message from every IBM WebSphere MQ queue, but all attempts failed.

The CTD30AI message will be issued and IBM WebSphere MQ decollation will be stopped.

Review previous messages and issue appropriate responses. After you perform the necessary corrections, issue the STARTMQ modify command.

Corrective Action: No action is required.

REP30DI MQ QUEUE IS BEING CLOSED BECAUSE PUT/GET IS FAILED, QUEUE NAME queueName

Explanation: The access to the IBM WebSphere MQ Series queue queueName is being closed because of failure of MQPUT for the ESCAPE MQ queue, or failure of MQGET for the MQ queue.

Control-D continues processing MQ decollations until this message is issued for all MQ queues.

Corrective Action: For additional information see the IBM WebSphere MQ Series documentation set.

REP30EE MEMBER CTDMQPRM IS NOT FOUND IN CTD PARM OR VALUE OF MQNOTFIND PARAMETER IS NOT DEFINED

Explanation: The CTDMQPRM member was not found in CTD PARM, or the value of the MQNOTFIND parameter has not been defined.

The CTD30AI message will be issued and IBM WebSphere MQ decollation will be stopped.

Corrective Action: Define the CTDMQPRM member or add the name of the MQNOTFIND parameter; then issue the STARTMQ modify command.